B and Z Electric has been the go-to electrical contractor for homeowners and businesses in Huntersville since 2012. Over 14 years, we have built a reputation across Mecklenburg County for showing up on time, doing the work right, and leaving every property safer than we found it. Whether you need a quick repair or a full panel upgrade, we are the local crew that gets it done.
We power your home. We protect your circuits. We earn the call.
The hardest part of an electrical problem is knowing when to call, and the answer is usually sooner than you think. Flickering lights, dead outlets, and breakers that trip without warning are not just nuisances. They are symptoms of something that needs a real look from someone who knows what they are doing.
When you call us, a licensed electrician diagnoses the problem at the source. We check the circuit, trace the fault, and explain what we find before any work begins. We handle breaker replacement, GFCI and AFCI protection upgrades, outlet repairs, wiring shorts, and anything else that is keeping your home or business from running the way it should. Every repair comes with code-compliant wiring on every job, so you are not just getting a quick patch. You are getting it done properly.
We make the fix and leave it tidy.
Don't let a small wiring issue turn into a fire risk, especially in a home that was built before today's electrical loads were even imagined. Huntersville has a mix of newer construction and older homes, and both can run into panel and wiring challenges. A 100-amp panel that made sense decades ago may not keep up with a modern kitchen, a home office, and an EV charger all running at once.
We handle breaker panel repair and replacement, 100-to-200 amp service upgrades, and fuse box replacements. For older properties, we also do whole-house rewiring, knob-and-tube replacement, and aluminum wiring remediation. Our licensed electricians perform load calculations before any upgrade to make sure the new panel is sized right for your actual needs, and all work meets current code for grounding and bonding.
We take pride in the electrical work we leave behind, and panel work is where that shows most.
Your panel is in good hands with us.
Getting your electrical problem handled starts with a quick call. But not every call is about a problem. A lot of what we do is helping homeowners make their space work better: adding outlets where there are never enough, swapping in dimmer switches, or getting a ceiling fan wired properly in a room that has never had one.
We install GFCI outlets in kitchens, bathrooms, and garages where code requires them, and AFCI breakers in living areas and bedrooms for added arc-fault protection. We also handle USB outlets, light switch replacement, and smart dimmer installation. On the lighting side, we do recessed and LED lighting layouts, under-cabinet lighting, light fixture installation, and outdoor and security lighting. Motion sensor lights for driveways and entry points are a popular request, and we wire them to last.
Ceiling fan installation is one of our most common residential calls, and we do it right, including proper bracing if the box needs it. Clear communication from the first call to the final test means you know what to expect before we touch a single wire.
Pick up the phone and we'll get rolling.
We know schedules shift, so we keep booking flexible, but some electrical upgrades are worth planning ahead for. Huntersville has grown fast, and with that growth comes more demand for modern electrical infrastructure in homes that were not always built with it in mind.
Dedicated circuits for dryers, ranges, refrigerators, and other large appliances protect both the appliance and the panel. We install 240-volt outlets and run the circuits with the capacity the equipment actually needs. For homeowners adding an electric vehicle, we install Level 2 EV charger circuits that give you a full charge overnight without stressing the rest of your electrical system.
Whole-home surge protection is something more Mecklenburg County homeowners are asking about, and for good reason. A single power surge can damage electronics, appliances, and HVAC systems in seconds. We install surge protection at the panel level so the whole house is covered. For backup power, we handle generator hookups and transfer switch installation, including automatic transfer switches that kick in without you having to do anything when the lights go out.
We're ready to get your circuits working again.
Property managers and business owners in the area count on us for commercial electrical work that gets done on schedule and up to code. We handle commercial panel upgrades, office and retail electrical installations, warehouse lighting, and electrical permit work for build-outs and renovations. If a property has a code violation that needs to be corrected before an inspection, we can assess it, pull the permit, and make it right. Work is performed by licensed electricians who understand commercial requirements and know how to coordinate with other trades on a job site.
We're ready to get your circuits working again.
Getting your electrical problem handled starts with a quick call, and that call should never feel like a guessing game. We give you no-pressure estimates, priced up front, so you know what the job costs before we start. If something unexpected comes up during the work, we tell you about it before we proceed. No surprises on the invoice.
We offer same-day service when the schedule allows and are available for after-hours electrical emergencies. We pick up the phone and get it handled. When you call, you reach someone who knows the area and can get a crew to you quickly.
Local crew. Real electrician on the phone. Quick to respond.
We're ready to get your circuits working again.
Every job we take on, from a single outlet to a full panel replacement, is completed to current electrical code. That is not just a legal requirement. It is how we make sure the work is actually safe for the people living or working in the space. We do not cut corners to save time, and we do not close up a wall until we are confident the wiring behind it is right.
After the work is done, we test every circuit, confirm all connections are solid, and walk you through what was done and why. If a permit is required, we pull it. If an inspection is needed, we schedule it. Safe, code-compliant electrical work is the standard we hold ourselves to on every visit, every time.
We test every circuit. We label every breaker. We leave it safe.
We are based in Huntersville and do most of our work right here in Mecklenburg County. Over 14 years, we have built relationships across the area and know the neighborhoods, the housing stock, and what local homeowners and businesses actually need from an electrician.
Beyond Huntersville, we regularly serve:
If you are in the area and need an electrician, there is a good chance we have already worked on a home or business near you.
We have been doing this work since 2012, which puts us at over 14 years of electrical service in Huntersville and Mecklenburg County. Over that time we have built relationships across the area and developed a solid understanding of the local housing stock and what homeowners and businesses here actually need from an electrician.
Yes. We are a locally owned business based in Huntersville. When you call, you reach someone who knows this area and is personally accountable for how the work turns out. That local connection matters to us on every job.
We believe electrical work should be done right the first time, communicated clearly throughout, and priced honestly before anything begins. We take pride in the work we leave behind, and we hold that standard on every job whether it is a single outlet or a full panel replacement.
We serve homeowners, landlords, property managers, small business owners, office managers, retail operators, and general contractors throughout the Huntersville area and northern Mecklenburg County. Residential and commercial customers both call us regularly, and we handle both sides well.
We pick up the phone and get it handled. Same-day service is available for repairs and urgent work when the schedule allows, and we are available every day from 8:30 AM to 11:00 PM. When you call, you reach someone who can give you a real answer about availability right away.
Work is performed by licensed electricians who know the code and take it seriously. We do not guess, we do not patch over symptoms, and we do not close up a wall until we are confident the wiring behind it is right. Clear communication and honest pricing are part of every visit, not just the ones where something goes well.
We do. A significant part of our work is commercial electrical service for small businesses, retail locations, office spaces, and property managers across Huntersville and the surrounding area. When a local business needs electrical work done right and on schedule, we are a reliable call.
We stand behind everything we do. If something we worked on is not right, we want to know about it and we will make it right. We take pride in the electrical work we leave behind, and that accountability does not end when we pull out of the driveway.
We respect your time and communicate clearly about when to expect us. If something shifts on our end, we let you know. Showing up when we say we will is part of how we build trust with customers in Huntersville and the surrounding communities.
B and Z Electric has been serving Huntersville and Mecklenburg County since 2012, and we are ready to help with whatever electrical work you have on your list. Call (980) 246-2289 to get a quote or schedule a service visit.
We power your home. We protect your circuits. We earn the call.
We handle the full range of residential and commercial electrical work in Huntersville and throughout Mecklenburg County. Whether you need a quick repair or a major panel upgrade, the table below covers what we do, who each service fits best, and what to keep in mind before you call. Work is performed by licensed electricians on every job, and we give you a price before anyone touches a wire.
| Electrical Service | What's Included | Best For | Good to Know |
|---|---|---|---|
| Breaker & Fuse Repair | breakers that trip repeatedly, failed breakers, fuse panel issues | homes where a circuit keeps going out or a breaker will not hold | A breaker that trips repeatedly is often a sign of an overloaded circuit or a failing breaker, not just a nuisance. We find the cause, not just the symptom. |
| Wiring for Additions & Remodels | electrical rough-in, remodel circuit work, tenant build-outs, addition wiring | contractors and homeowners adding square footage or finishing existing space | We work with general contractors and property managers who need a reliable electrical sub. We show up when we say we will and keep the work area clean. |
| Dedicated Appliance Circuits | dryer and range outlets, 240-volt receptacles, workshop circuits, large appliance feeds | homeowners adding a major appliance, finishing a basement, or setting up a workshop | Dedicated circuits need to be sized and wired correctly for the appliance they feed. We run them right the first time. |
| Wiring & Circuit Installation | new circuit runs, whole-home rewiring, service entrance upgrades, code-compliant wiring | homes being renovated, expanded, or brought up to current electrical standards | Knob-and-tube and aluminum branch-circuit wiring both create safety and insurance concerns. We replace outdated systems with wiring that meets current code. |
| Backup Generator Installation | transfer switch installation, standby generator wiring, generator hookup, dedicated generator circuits | homeowners and commercial properties that need power reliability during storm outages | Storm season in this part of North Carolina is real. A properly wired transfer switch keeps your home running safely when the grid goes down. |
| EV Charger Installation | Level 2 charger circuits, 240-volt outlet installation, hardwired EVSE hookup, panel capacity check | homeowners adding an electric vehicle and needing a reliable home charging setup | We size the circuit correctly and confirm the panel can carry the added load before the charger goes in. The circuit has to be right before anything else happens. |
| Ceiling Fan Installation | new fan installation, fan replacement, box upgrade for fan support | homeowners replacing a light fixture with a fan or swapping out an old fan | If the existing box is not rated for a fan, we replace it before the fan goes up. Skipping that step is a safety issue we do not overlook. |
| Whole-Home Surge Protection | panel-level surge protection, dedicated circuit protection, lightning strike defense | any home with sensitive electronics, appliances, or equipment worth protecting | A single nearby lightning strike can damage electronics throughout the house in an instant. A whole-house surge protector at the panel catches that spike before it reaches your circuits. |
| Lighting Installation | recessed lighting, pendant and chandelier installation, security and motion lights, landscape lighting | homeowners updating interior lighting or adding exterior security and curb appeal | Exterior lighting is one of the most practical upgrades for safety and property value. We handle both the fixture and the circuit. |
| Electrical Repairs & Troubleshooting | dead outlets, flickering lights, partial power loss, tracing faults to the source | homeowners or landlords dealing with an unexplained electrical problem | We check GFCI faults, loose connections, and overloaded circuits before recommending any work, so you get an accurate diagnosis first. |
| Outlet & Switch Installation | GFCI outlets, USB outlets, dimmer switches, smart switch upgrades | homeowners updating older wiring or adding modern outlets without a full renovation | Ungrounded outlets in older homes are a safety and insurance concern. We address grounding as part of the work, not as an add-on. |
| Older-Home Rewiring | knob-and-tube replacement, aluminum wiring remediation, whole-home rewire, grounding and bonding upgrades | owners of older homes with wiring that creates safety or insurance concerns | Older wiring systems are not just a code issue. Many insurers will not cover a home with knob-and-tube or ungrounded aluminum branch circuits. We replace it with code-compliant wiring throughout. |
| Electrical Safety Inspections | pre-purchase inspections, wiring condition assessments, panel and circuit review | buyers, sellers, or owners who want a clear picture of their home's electrical condition | An inspection before a home sale or purchase can surface issues that affect both safety and negotiating position. We give you a straight report. |
| Electrical Panel & Service UpgradesMost Popular | 200-amp service upgrades, subpanel installation, main panel replacement, load calculation | homes with older 100-amp panels or any property adding significant new electrical load | A single EV charger or home addition can push an older panel past its limit. We walk you through the job before we start and do not consider it done until the panel is tested and labeled. |
| Basement & Sump-Pump Circuits | basement finishing circuits, dedicated sump-pump circuit, GFCI protection in below-grade spaces | homeowners finishing a basement or adding a sump pump to a wet-prone area | Sump pumps need a dedicated circuit so they are not competing with other loads when you need them most. We wire it correctly and protect it with the right GFCI coverage. |
What are the signs that my electrical panel needs to be upgraded?
A few things point clearly to a panel that has reached its limit. Breakers that trip often under normal loads, a panel that feels warm to the touch, lights that dim when an appliance kicks on, and a panel that is already full with no open slots are all common indicators. Older 100-amp panels were sized for households that used far less power than today's homes. If you are adding an EV charger, a home addition, or a large appliance, a capacity check is worth scheduling before you run into problems.
Why does my breaker keep tripping?
Repeated tripping usually means one of three things: the circuit is overloaded and drawing more current than it was designed to handle, there is a fault somewhere in the wiring or a connected device, or the breaker itself is worn and failing to hold its rated load. We trace the cause before recommending anything. Sometimes it is as simple as redistributing loads across circuits. Other times the circuit needs to be upgraded or a breaker replaced. We give you a clear answer before any work begins.
Is the electrical work permitted and inspected?
When a permit is required for the scope of work, we pull it. When an inspection is required, we schedule it. Code-compliant wiring on every job is not just a phrase we use; it is how we run every project. Work is performed by licensed electricians who know what the current code requires and take it seriously.
Upfront Quotes With No Surprise Fees
We give you a price before any work begins and we do not start until you have agreed to it. What we quote is what you pay, with no charges added after the fact.
How do I know if the wiring in my older home is safe?
Homes built before the 1970s sometimes still carry knob-and-tube wiring or aluminum branch-circuit wiring. Both create real safety and insurance concerns. Signs of trouble include frequently tripping breakers, outlets that are warm to the touch, a burning smell near outlets or the panel, and outlets that are two-prong rather than grounded three-prong. An electrical safety inspection gives you a clear picture of what you are working with. We walk through the home, check the panel, and give you a straight report on what we find.
What does an EV charger installation involve?
A Level 2 home charger requires a dedicated 240-volt circuit run from your panel to the garage or driveway location where the charger will live. We size the circuit for the charger's amperage requirements, confirm the panel has the capacity to carry the added load, and install either the outlet or the hardwired connection depending on your charger. If the panel needs an upgrade to accommodate the new circuit, we handle that as part of the same project.
What does backup generator hookup include?
We handle the electrical side of a generator installation: the transfer switch, the wiring from the panel to the switch, and the connection point for the generator. A properly installed transfer switch is what makes a generator safe to use during an outage. It isolates your home's circuits from the utility line so power does not backfeed into the grid. We wire the system to code and test it before we leave.
Work Performed by Licensed Electricians
Every job we complete is handled by licensed electricians who know the code and take it seriously. We pull permits when required and schedule inspections when the work calls for it.
Do I need to be home while the work is being done?
For most jobs, yes, someone should be available at the start so we can walk through the work and confirm the scope before we begin. For larger projects that span more than one day, we can discuss what access looks like after the first visit. We communicate clearly about what to expect at each stage so there are no surprises.
How does pricing work?
We give you a price before any work begins. We do not start until you have agreed to it, and we do not add charges at the end that were not discussed upfront. For standard repairs and installations, payment is collected when the job is complete. For larger projects like whole-home rewiring or a full panel replacement, we talk through payment expectations when we go over the estimate.
Experienced With Older and Newer Homes
We work on homes across the full range of Mecklenburg County housing stock, from older in-town properties with dated wiring to newer subdivisions adding capacity for modern loads. We bring the right approach to each one.
Are you available for same-day or emergency electrical calls?
Same-day appointments are available for repairs and urgent calls when the schedule allows. We are available every day from 8:30 AM to 11:00 PM, including weekends. If something goes wrong in the evening or on a Saturday, you can still reach us. Call early in the day for the best chance at a same-day visit.
What does it mean if my outlets feel warm or make a buzzing sound?
A warm or buzzing outlet is not something to ignore. It can indicate a loose connection, an overloaded circuit, or a failing outlet that is generating heat it should not be. In older homes, it sometimes points to wiring that is not sized for today's loads. We recommend calling sooner rather than later when you notice either of those signs, because the risk of a wiring fire increases the longer the condition goes unaddressed.
Does my home need GFCI protection, and where?
Current electrical code requires GFCI protection in kitchens, bathrooms, garages, outdoor locations, crawl spaces, and unfinished basements. Older homes often lack GFCI outlets in some or all of these areas. We install GFCI outlets and breakers as standalone work or as part of a larger project. If you are unsure whether your home meets current requirements, an inspection is a straightforward way to find out.
Call (980) 246-2289 to talk through your electrical job and get a quote from a local crew that knows this area.
(980) 246-2289